ASTM A488 PDF

Referenced Documents ASTM Standards: A 27/A 27M Specification for Steel Castings, Carbon, A /A M A /A M Specification for Castings. ASTM A – 4CTb Designation: A /A M – 01” An American National Standard Standard Pra. 费下载 免 w 焊接人 w Designation: A /A M – 07 Standard Practice for Steel Castings, Welding, Quali?cations of.

Author: Kakora Turisar
Country: Uruguay
Language: English (Spanish)
Genre: Literature
Published (Last): 15 December 2005
Pages: 57
PDF File Size: 3.65 Mb
ePub File Size: 14.94 Mb
ISBN: 610-6-99505-851-9
Downloads: 21100
Price: Free* [*Free Regsitration Required]
Uploader: Kajikazahn

Also indicate whether preheat is requimd dwing metal mal. Carbonmanganese steel tensile strength equal to or greater than 70 ksi but less than 90 ksi [ MPa]. The orientation of the welds with respect to the horizontal and vertical planes of reference is classified into four positions, namely, flat, horizontal, vertical, and overhead.

Post-Weld Heat Treatment Root Bend 2 Either the face- and root-bend tests or the side-bend tests may be used for thicknesses from 3? The notch shall be cut normal to the material surface in the heat-affected zone to include as much heat-affected zone as possible satm the resulting fracture Fig.

Qualification under any F number up to and including F4 shall qual a welder for all lower F numbers. Combining values from the two systems may result in nonconformance with this practice. The welder or operator asym performing the procedure qualification test is automatically qualified for performance. Types of Tests s488. Originally published as A 63 T. Preparation of Test Plate 5. Groove dimensions as shown in Fig. P-number designations in the ASME grouping of base metals for qualification may be different than the category numbers listed in Table 1.

  HELENA BERISTAIN DICCIONARIO DE RETORICA Y POETICA PDF

This standard is a4888 to revision at any time by the responsible technical committee and must be reviewed every? A Indicate appropriate American Welding Society speci? A bend axtm comprised of parent metal heat treated to the ductility and strength requirements of the applicable specification shall be bent to failure.

Root Bend 2 B Indicate whether electrode positive EP or electrode negative EN output terminal of power supply is used. A suggested ashm for recording such information is shown in Fig. A Indicate minimum distance for local preheating. ASTM D e1. Requalification of Welders and Operators The other two surfaces shall be called the face and root surfaces, the face surface having the greater width of weld. When two base materials having different category astmm are welded together, a procedure qualification must be performed for the combination.

Each specimen shall be tested and meet the requirements of 8.

Welding shall be asm without rotating the pipe or casting so that the weld metal is deposited from the? A total of four specimens are required to qualify for Position 1 e of Fig.

ASTM AAM 钢铸件焊接程序和人员资格的标准实施规程_百度文库

Manufacturer or Contractor Date: E Weld should be in center of reduced section. Originally approved in Qpes of Tests 6.

If a recessed ring is used, this surface of the specimen may be machined to a depth not exceeding the depth of the recess to remove the ring, except that s488 such cases the thickness of the?

Tensile strength equal to or greater than 85 ksi [ MPa]. Guided Bend Test 8.

All welders and operators welding castings under this practice shall pass the welder qualification test. Test material shall be oriented as shown in Fig.

  INTRODUCTION TO LOGIC DESIGN ALAN B MARCOVITZ PDF

Where the material thickness permits, the axis of a heat-affected zone specimen may be inclined to allow the root of the notch to align parallel to the fusion line Fig. The welding procedure shall be in accordance with that given in the procedure quali?

A Indicate the number for controlling the maximum width. The cut surfaces shall satm designated the sides of the specimen. Alternatively, the entire weld shall be removed and replaced by a quali?

Standard Practice for Steel Castings, Welding, Qualifications of Procedures and Personnel

Preparation of Base Material. P-number designations in the ASME grouping a48 base metals for qualification may be different than the category numbers listed in Table 1.

Each specimen shall be tested and meet the requirements of 7. However, cracks occurring on the corners of the specimen during testing shall not be considered unless there is de?

The side of the specimen turned toward the gap of the jig shall be the face for face-bend specimens, the root for root-bend specimens, and the side with the greater number of defects, if any, for side-bend specimens. This standard has been approved f o r use by agencies of the Department of Defense. Carbonmanganese steel tensile strength equal to or greater than 70 ksi but less than 90 ksi [ MPa]. A Indicate degree of interpass inspection required.