ASTM A666-10 PDF

ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.

Author: Kigarisar Vudolabar
Country: Zimbabwe
Language: English (Spanish)
Genre: Love
Published (Last): 23 September 2013
Pages: 350
PDF File Size: 15.97 Mb
ePub File Size: 14.64 Mb
ISBN: 629-5-96569-462-7
Downloads: 68891
Price: Free* [*Free Regsitration Required]
Uploader: Kazrashura

If filler metal is required, Type is normally used.

Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part. In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work. Material Test Report and Ast, HRC typical L Ann 25 min.

Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed asstm non-marine atmospheres Chemical Composition: Only annealed conditions of grades speci?

Annealed Types and L can be fabricated by roll forming, deep drawing, bending and a666-100 other fabrication techniques. However, in the case of dispute, a666-10 shall be made by pressure. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

  HINK PINKS PDF

and L Stainless Steel – NKS

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Current edition approved Sept. Type L Stainless Asfm is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld.

C Annealed material that naturally meets mechanical properties a66-610 be applied. Permission rights to photocopy the standard may also be secured from the ASTM website www.

a666–10 A — 10 Standard Speci? Maximum unless otherwise indicated. The noncontrolling factor normally will exceed considerably the speci? The values obtained in this manner should not, however, be taken as the actual yield strength for 0.

HardC Elongation in 2 in.

A number in parentheses indicates the year of last reapproval. Last previous edition approved in as A — Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties.

Rockwell B 95 95 In case of dispute, the offset method of determining yield strength shall be used. Types and L cannot be hardened by thermal treatment. If you feel that your comments have not received a fair hearing you should make asrm views known to the ASTM Committee on Standards, at the address shown below.

Hard Elongation in 2 in. The choice of test method for materials in conditions other than annealed shall a666-100 at the option of the seller. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. The values given in parentheses are for information only. Types and L are weldable by most fusion or resistance welding techniques. Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?

  HORTICULTOR AUTOSUFICIENTE PDF

Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: Number of Tests 8.

304 and 304L Stainless Steel

D PSS means plate, strip, sheet. Originally approved in Find out what NKS can do for you.

Type L LN Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres.

Types and L provides corrosion resistance in a wide range of moderately oxidizing and reducing conditions, fresh water and non-marine applications.

These alloys represent an excellent atsm of corrosion resistance and fabricability. This standard has been approved for use by agencies of the Department of Defense.

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci?